The S700 SEAMLESS is JESCO Lighting’s premier low voltage LED linear fixture. Each S700 fixture is linkable end- to-end with no dark spots even at connections between fixtures or connectors. Inter-connectable lit L- type corners provide for seamless turns – clockwise, counter- clockwise, inside-facing and outside- facing – allowing the fixture to change directions either on a horizontal or a vertical plane. Lit X- and T- type connectors are also available for a wide range of design possibilities. A uniform light output allows for intricate and complex layouts free from any break in the flow of light.
The S700 SEAMLESS is a low- profile slim fixture measuring at only 7/16”W x 1/2”H. It is the ideal fixture for a variety of applications such as:
The S700 SEAMLESS is a truly a unique and innovative fixture in the low voltage rigid linear LED lighting category. It is packed full of features that sets it apart from standard linear LED fixtures such as:
Reliable, sophisticated, installation- friendly and code- compliant. All of which add up to a turn key product line that remains the industry leader today.
The maximum continuous run length for the S700 SEAMLESS is 16.4 feet. However, runs may be seamlessly extended with the use of S700-EXTBSF. It is an in-line connector that allows two separately powered runs to be linked seamlessly for an extended uninterrupted run. It also allows for closed-circuit shapes such as squares and rectangles. The cable on the S700-EXTBSF can exit from the back or from the side to allow for easy wire management no matter the application.
This, coupled with the fact that S700 SEAMLESS has IC chips ensures that there is almost zero light output loss from the beginning to the end of runs, allowing designers to extend the run as long as they want without any visible output variation, color variation, or break in the flow of light.
Yes, the S700 SEAMLESS is dimmable using a variety of methods. We offer an in-line touch ON/OFF switch and dimmer with memory, S700-DIM. The fixture can also be dimmed with 0- 10V dimmers using our 0 – 10V dimmable drivers and with Triac dimmers using our TRIAC dimmable drivers. Please see the S700 SEAMLESS Specification Sheet for more details.
From resistive dimming to full DMX control, JESCO has a dimming solution no matter what you need– contact JESCO customer service for assistance with your next lighting control specification.
Lit inside and outside connectors in L, X and T patterns allow for lighting designs in three dimensional planes. We also offer connecting cables in 6”, 12” and 24” length options to go around corners.
Each fixture comes with a live end cap, a dead end cap and mounting brackets.
Once the fixture has been installed, the live end of the fixture is connected to either the power cord or the previous fixture, so the live end cap can be discarded once the fixture has been installed.
A dead end cap must be used to terminate the end of every run. Apart from providing protection from dust and moisture, it also provides a finished look to the fixture.
Mounting is achieved by using the imbedded magnets for metal surfaces. Snap- in, fixed mounting brackets S700-BR (provided) and 45 degree mounting brackets S700-BR45 are also available for non-metallic surfaces. The fixture may also be mounted onto non- metallic surfaces with optional metal tabs ACC-MC- MET- 01 that interact with the imbedded magnets.
The S700 is UL Listed as suitable for damp locations
No. All LEDs need DC current to operate properly. You can use any of our 24V DC DL- PS LED drivers to power the S700 SEAMLESS. We offer drivers and power connectors in both Plug & Play and Hardwire options.
Yes, contact your JESCO representative or our general offices to find out availability of higher wattages and higher lumen outputs to meet your project requirements.
Yes, contact your JESCO representative or our general offices to find out availability of S700 with Full Spectrum LEDs to meet your project requirements.
Typically, you will not see any failures in our S700 for many, many years. In the rare event of a premature failure, a section can be replaced within an installed run by simply unplugging the bad section and replacing it with a new one.
Yes, The S700-DIM an in-line touch ON/OFF switch and dimmer with memory
The LEDs used in the S700 are designed to meet or exceed a Rated Lumen Maintenance Life or L70 of50,000 hours (Meaning the LEDs will maintain at least 70% of their original light output after the fixture has been on for 50,000 hours).
That being said, exceeding the operating temperature values may damage the LEDs by reducing the lifespan, lumen output, and/or adversely impact color consistency. It is recommended that adequate airflow and heat sinking be taken into consideration in the installation and application of this product. Improper thermal management may lead to premature product failure and void the warranty.S ee the product specification sheets for more information.
Please see the S700 SEAMLESS specification sheet for wiring diagrams.
LEDs have caused a revolution in lighting. JESCO has helped lead that revolution.We were one of the first manufacturers to make the shift to the LED light source many years ago. Our LEDs are of the highest quality and they are time- tested to be dependable.
There are many reasons to make the switch to LED products. Some of the reasons include:
Technological Impact
LEDs are solid state, light emitting chips that are not encased in fragile glass enclosures or use delicate and inefficient filaments. LEDs are vibration resistant. They also do not need to warm up as they are an instant- on light source. LEDs currently offer life expectancy of 50,000 hours, on average. LEDs offer much more control of correlated color temperatures and provide the option to add color(s) either monochromatically or through RGB technology. The chips are miniscule in size which allows manufacturers to design much smaller fixtures and allows designers and end users much greater flexibility incorporating and installing these fixtures on their projects.
Financial Impact
The long life expectancy means a higher rate of return on investment – installed fixtures can last, at least, 10 years (depending on the design, the lifespan of the power source and the duty cycle of the fixture) with no maintenance. No maintenance means n o labor costs and no replacement lamp costs associated with installed fixtures and lamps over the life of the fixture. Fixtures mounted in high or hard- to-reach locations are the prime candidates for LED lighting. LEDs are very efficient light sources and are cool to the touchunlike incandescent light sources which release 90% of their energy generated as heat. Due to the inherent cooler running temperatures of LEDs, HVAC system design loads can be scaled down. LEDs use much less energy per fixture than standard light sources guaranteeing savings in electrical costs far into the future. Lastly, many local energy providers are currently offering rebates to customers making the switch to LED fixtures.
Environmental Impact
LEDs are easily recyclable. They contain no mercury or lead which require special handling and disposal. LEDs do no emit harmful UV/IR which discolors fabric, furniture and artwork. The U.S. Department of Energy estimates that rapid adoption of LED lighting in the U.S. by 2027 could deliver savings of about $265 billion, avoid the building of 40 new power plants and re duce lighting electricity demand by 33% in 2027.
All or even one of the above stated reasons may be the right reason for you to choose a fixture with an LED light source.
The last important factor when choosing an LED fixture is scrutinizing the manufacturer of the LED chip and the incorporation of this chip into the design of the lighting fixture. As the United States EPA and DOE Energy Star program states on its website “Bad design can lead to a wide range of problems, some immediately observable and some not. Poorly designed products often come with exaggerated claims while failing to deliver on the quality specifications provided.” Our LED products are designed around the LED light source and not the other way around making for a well- designed, color consistent and extra long- life fixture with a proven track record. With all our LED products, JESCO offers layout assistance and technical support helping make specification, as well as installation, simple.
Therefore, always look for reputable and trusted sources of LEDs and LED fixtures – be it JESCO Lighting or anyone else.
The S601 Slim Stix can be used anywhere a vanishingly small and very bright source of light is needed. The most common uses remain under/above cabinet, cove and display case illumination. We have created an impressive range of accessories to support code-compliant installation all of the different uses that this product can have.
The important differences between S601P and other similar-looking products are as follows:
Reliable, sophisticated, installation-friendly and code-compliant. All of which adds up to a turnkey product line that remains the industry leader today
Yes. JESCO’s PWM (Pulse-width modulation) dimmer, the LC-DIM-5A, offers full range dimming. Options within our dimming products facilitate installation conditions ranging from a simple knob on a power cord (LC-DIM-5A), through to residential architectural wallplate dimming (LC-DIM-5A-HW & DSDV-TV) and on through to the largest imaginable commercial building control systems (LC-DIM-5A-HW + any control system with 0-10V interface).
The S601P prefers to be controlled by 0-10V capable building control systems, but it is also able to communicate to multiple other industry-standard protocols if need be.
From the very simplest knob mounted under a counter through to interfacing with complex energy management systems JESCO has a solution – contact JESCO customer service for assistance with your next lighting control specification.
As you may or may not know, JESCO’s S601 LED fixtures have all been independently tested by Lutron and Crestron. After conducting their testing, both companies have confirmed that our products are among the few that will work seamlessly with their many dimming options. Test results are available on the Lutron website – search “JESCO” on the Lutron site.
Unlike many of the LED fixtures in the market, JESCO’s product is well suited for incorporation into high-end residential homes and commercial spaces using the very best dimming systems available due to our constant current design and our proprietary dimming controller, the DIM-5A. In fact, Lutron has just modified their GRAFIK Eye® dimmer to better integrate their controls with our fixtures. They have introduced a new model number, #GRX-TVI-CPN6267, into their product offering tailored to our S601.
The new Lutron dimmer, model number GRX-TVI-CPN6267, is the recommended version if the dimming design plan calls for using a GRAFIK Eye® dimmer. Until this change is added to their standard dimmer, this is a custom version dimmer (pricing should be the same or close as the standard) and available through normal Lutron distribution channels with 1 to 2-week lead-time. You can also find out how to get this dimmer on their website HERE.
If you have any questions on dimming choices visit the Lutron or Crestron websites or contact our technical department directly at support@jescolighting.com
JESCO has tested up to 7 x LC-DIM5A-HW interfaces per each 0-10V wallplate dimmer (LC-DIM-5A-HW & DS-DV-TV for instance).
In reality, because the LC-DIM-5A is a high impedance input product drawing only a few milliamps (~7mA) per device, it is likely possible to connect many more than 7 devices to most systems on the market. We have not tested operation beyond 7 devices at JESCO though.
The LC-DIM5A-HW is both a current-source and current-sink compatible device – enabling it to work successfully on most control manufacturer’s equipment.
24 volts DC is the standard operating voltage for the product line. For the S601 system, we recommend our DL-PS-xx/24 series of power supplies. Refer to the specification sheets for JESCO’s DL-PS line of LED power supplies and drivers for more information.
Typically the necessary power supply will install on a single 15 or 20 Amp circuit.
24V power distribution was selected in order to render the longest, brightest and most consistently lit fixture runs while at the same time complying with the complex UL and NEC code restrictions you will come across on job sites.
Additionally, each section of S601P product has high performance, locally mounted board-mounted LED drivers – typically 3 per foot of fixture – meaning that each LED is carefully supervised by its own LED driver. This method ensures consistent operation throughout each run and LED longevity combined with immunity to local power supply fluctuation and normal power distribution shortcomings – a JESCO innovation unmatched in the industry
JESCO DL-PS power supplies can operate at 120 volts, 277 volts and other European and international power utility company supply voltages. Many of our DL-PS plug-connected power supplies also have the ability to accept world-market power cords (by others) permitting operation in multiple territories with one single product – one product for the entire world in other words.
For our S601 series, the maximum continuous installed run length is 20 feet per each home run to a ower supply.
8” is the minimum length that can be purchased from JESCO. Please note that our DL-PS electronic power supplies do not have a minimum load requirement but our DL-PS magnetic power supplies do. Please check the specification sheets for the exact requirements of the chosen power supply.
To get around obstacles we offer flexible connecting cables in lengths from 3” to 48”. Connectors are typically used to create unlit sections and/or to jump power around obstacles or through walls. JESCO has set up its power supply and fixture UL listings to permit Class 2 power feeds to go through walls, etc. using our jumpers as well as contractor-created hardwire jumpers – consult your electrical contractor or authority having jurisdiction for the exact regulations in your locale. All the cables within the JESCO S601 system can be interconnected and you can use multiple connector lengths together to achieve a certain distance.
We offer the S601-R-CONN and S601-L-CONN hard right and hard left connectors. The S601-LEXCONN is a flexible product that allows for angles under 90 degrees
The S601 mounts with our standard mounting clip, S601-MC, which allows for 30-degree rotation. Two of each is included with each fixture. We also offer a single 6-foot mounting channel, S601-CH6, where the S601 can be mounted directly or at a 45-degree angle. The S601-CH6T is a 6-foot mounting channel for two S601 that again allows the fixtures to be mounted directly or at a 45-degree angle.
No, the S601P is not designed for use in wet locations
Yes, we provide desktop or wall plug drivers that produce the 24V DC power which plug into a standard wall outlet. See JESCO DL-PS-xx/24 series of plug-and-play LED drivers.
In order to eliminate voltage drop, cables specifications of 14/2 AWG and up are typically used.
Your contractor will assist you in specifying the correct gauge of cable required to remotely locate the power supply relative to your fixture location and to determine how to eliminate voltage drop from remote supplies.
Typically you should think in terms of 20’ – 50’ max feeds to/from remote locations, although any distance is theoretically possible with your contractor’s assistance in the specification of correct supply cables.
Yes, contact you JESCO representative or our general offices to find out the availability of higher wattages and higher lumen outputs to meet your project requirements.
We offer our LEDs in Kelvin color temperatures of 3000-3300°K, 4000-4400°K, and 6000-6500°K.
The lower the color temperature the warmer the color – 3000°K is considered warm white and 6000°K is considered cool white.
Typically, you will not see any failures in our S601 for many, many years. In the rare event of a premature failure, a section can be replaced within an installed run by simply unplugging the bad section and replacing it with a new one
Yes, we offer the S601-SW in-line switch box that can plug directly in between S601 fixtures or be connected with our connecting cables.
Recommended applications for the S601 series include coves, display cases, offices stores and restaurant, architectural features, corporate showrooms and exhibition display, residential shelves and counters, accenting point of purchase display, signage applications, backlighting of glass and acrylic panels or cut out forms, lighting toe-kick areas, undercabinet task lighting.
JESCO LEDs in the S601 family are designed to meet or exceed a Rated Lumen Maintenance Life or L7 0 of 50,000 hours (Meaning the LEDs will maintain at least 70% of their original light output after the fixture has been on for 50,000 hours).
That being said, exceeding the operating temperature values may damage the LEDs by reducing the lifespan, lumen output, and/or adversely impact color consistency. It is recommended that adequate airflow and heat sinking be taken into consideration in the installation and application of this product. Improper thermal management may lead to premature product failure and void the warranty.
See the product specification sheets for more information.
We offer LEDs in specific white color temperatures. All our LEDs are designed to maintain their color over time and across the maximum length of a run.
We exceed the market’s highest standards by specifying the exact color bins when we select LEDs so that they do not fluctuate more than ±200° for warm color temperatures and ±300° for cool color temperatures. This meets or exceeds the recognized standards for color quality and guarantees uniformity and consistency of hue and color temperature across LEDs, fixtures, and manufacturing runs.
That being said, inherent to any commercial strip/tape product, individual LEDs within a strip may vary slightly but the overall color temperature of the strip/tape will fall within our tight specifications listed above.
Additionally, each section of S601P product has high performance, locally mounted, board-mounted LED drivers – typically 3 per a 1-foot fixture – which means that each LED is carefully supervised by its own LED driver. This method ensures consistent operation and longevity combined with immunity to local power supply fluctuation and power distribution shortcomings – a JESCO innovation unmatched in the industry.
LEDs have caused a revolution in lighting. JESCO has helped lead that revolution. We were one of the first manufacturers to make the shift to the LED light source many years ago. Our LEDs are of the highest quality and they are time-tested to be dependable.
There are many reasons to make the switch to LED products. Some of the reasons include:
Technological Impact
LEDs are solid-state, light-emitting chips that are not encased in fragile glass enclosures or use delicate and inefficient filaments. LEDs are vibration resistant. They also do not need to warm up as they are an instant-on light source. LEDs currently offer life expectancy of 50,000 hours, on average. LEDs offer much more control of correlated color temperatures and provide the option to add color(s) either monochromatically or through RGB technology. The chips are minuscule in size which allows manufacturers to design much smaller fixtures and allows designers and end-users much greater flexibility incorporating and installing these fixtures on their projects.
Financial Impact
The long life expectancy means a higher rate of return on investment – installed fixtures can last, at least, 10 years (depending on the design, the lifespan of the power source and the duty cycle of the fixture) with no maintenance. No maintenance means no labor costs and no replacement lamp costs associated with installed fixtures and lamps over the life of the fixture. Fixtures mounted in high or hard-to-reach locations are the prime candidates for LED lighting. LEDs are very efficient light sources and are cool to the touch, unlike incandescent light sources which release 90% of their energy generated as heat. Due to the inherent cooler running temperatures of LEDs, HVAC system design loads can be scaled down. LEDs use much less energy per fixture than standard light sources guaranteeing savings in electrical costs far into the future. Lastly, many local energy providers are currently offering rebates to customers making the switch to LED fixtures.
Environmental Impact
LEDs are easily recyclable. They contain no mercury or lead which require special handling and disposal. LEDs do not emit harmful UV/IR which discolors fabric, furniture and artwork. The U.S. Department of Energy estimates that rapid adoption of LED lighting in the U.S. by 2027 could deliver savings of about $265 billion, avoid the building of 40 new power plants and reduce lighting electricity demand by 33% in 2027.
All or even one of the above-stated reasons may be the right reason for you to choose a fixture with an LED light source.
The last important factor when choosing an LED fixture is scrutinizing the manufacturer of the LED chip and the incorporation of this chip into the design of the lighting fixture. As the United States EPA and DOE Energy Star program states on its website “Bad design can lead to a wide range of problems, some immediately observable and some not. Poorly designed products often come with exaggerated claims while failing to deliver on the quality specifications provided.” Our LED products are designed around the LED light source and not the other way around making for a well-designed, color-consistent and extra long-life fixture with a proven track record. With all our LED products, JESCO offers layout assistance and technical support helping make specification, as well as installation, simple.
Therefore, always look for reputable and trusted sources of LEDs and LED fixtures – be it JESCO Lighting or anyone else.
Sleek Ultra™ is the next generation of our award-winning, linkable Sleek Plus™ series. Using the same miniature profile and minimal footprint of our market-leading ‘mini fluorescent’ Sleek Plus™ fixture, we have engineered these fixtures to incorporate the latest in LED technology. These fixtures can be used in under cabinet, cove, and shelf lighting as well as backlighting of indoor signs and panels. The Sleek UltraT M can be linked for longer runs and is available in an adjustable version for better control of the light output.
The Sleek Ultra™ is a collection of high-performance fixtures. The important differences between JESCO’s Sleek UltraT M and other similar-looking products are as follows:
These products are a line voltage system and work at standard 120V.
The Sleek Ultra is linkable and has a maximum run length of 360 watts of total units.
This does not include any connections between the fixtures thereby extending the overall reach of the product. The overall maximum reach needs to be determined by a qualified electrician based on your power in the building.
No, there is no minimal installed length.
The Sleek Ultra series are provided with one direct connector, SG-DC. These direct connectors allow fixtures to be easily connected end-to-end to form one continuous run which provides a uniform and unbroken output of light.
The Sleek UltraT M product line has an extensive offering of grounded connecting cables for every application – from 6” to 36”
The Sleek UltraT M mounts with our mounting clips. Two 0⁰ and two 45⁰ clips are provided with each fixture. We also offer a vertical & horizontal 90⁰ clip and fully adjustable clip which helps meet any mounting situation you may encounter.
No, the Sleek Ultra is not designed for use in wet locations.
For wet location applications please refer to our DL-RS Rigid Strip LED wet location product line which is specifically designed for Wet and Outdoor installation conditions.
Yes, this product line plugs into any household or commercial three-prong outlet.
No. This is system is not dimmable. It is an on/off system only controlled by a remote or in-line switch in a metal box or in a plastic box. The SGA-LED comes standard with on/off rocker switch.
The SG-LED is available with a switch as an option.
We offer a standard straight power cord in various lengths (SG-PCxx) as well as a 6-foot right angle version that enters from the front (SG-PCLL) and a 6-foot right-angle version that enters from the back (SG-PCL) to help meet all your wiring needs.
The SGA-LED encloses the LED light source within its rotating lens. This lens easily rotates 360° allowing you the opportunity to control the direction of the 180° of light output as desired.
We offer our LED fixture in a White Kelvin color temperatures of 3000°K, 4000°K, and 6000°K.
The lower the color temperature the warmer the color – 3000°K is considered warm white and 6000°K is considered cool white
Typically, you will not see any failures in our Sleek Ultra for many, many years. In the rare event of a premature failure, a section can be replaced within an installed run by simply unplugging the bad section and replacing it with a new one.
Recommended applications for the Sleek Ultra series include coves, display cases, offices stores and restaurant, architectural features, corporate showrooms and exhibition display, residential shelves and counters, accenting point of purchase display, indoor signage applications, backlighting of glass and acrylic panels or cut out forms, lighting toe-kick areas, undercabinet task lighting.
JESCO LEDs in the Sleek UltraT M family are designed to meet or exceed a Rated Lumen Maintenance Life or L7 0 of 50,000 hours (Meaning the LEDs will maintain at least 70% of their original light output after the fixture has been on for 50,000 hours).
That being said, exceeding the operating temperature values may damage the LEDs by reducing the lifespan, lumen output, and/or adversely impact color consistency. It is recommended that adequate airflow and heat sinking be taken into consideration in the installation and application of this product. Improper thermal management may lead to premature product failure and void the warranty. See the product specification sheets for more information.
We offer LEDs in specific white color temperatures. All our LEDs are designed to maintain their color over time and across the maximum length of a run.
We exceed the market’s highest standards by specifying the exact color bins when we select LEDs so that they do not fluctuate more than ±200° for warm color temperatures and ±300° for cool color temperatures. This meets or exceeds the recognized standards for color quality and guarantees uniformity and consistency of hue and correlated color temperature across LEDs, fixtures, and manufacturing runs.
That being said, inherent to any commercial strip/tape product, individual LEDs within a strip may vary slightly but the overall color temperature of the strip/tape will fall within our tight specifications listed above.
LEDs have caused a revolution in lighting. JESCO has helped lead that revolution. We were one of the first manufacturers to make the shift to the LED light source many years ago. Our LEDs are of the highest quality and they are time-tested to be dependable. There are many reasons to make the switch to LED products. Some of the reasons include:
Technological Impact
LEDs are solid-state, light-emitting chips that are not encased in fragile glass enclosures or use delicate and inefficient filaments. LEDs are vibration resistant. They also do not need to warm up as they are an instant-on light source. LEDs currently offer a life expectancy of 50,000 hours, on average. LEDs offer much more control of correlated color temperatures and provide the option to add color(s) either monochromatically or through RGB technology. The chips are minuscule in size which allows manufacturers to design much smaller fixtures and allows designers and end-users much greater flexibility incorporating and installing these fixtures on their projects.
Financial Impact
The long life expectancy means a higher rate of return on investment – installed fixtures can last, at least, 10 years (depending on the design, the lifespan of the power source and the duty cycle of the fixture) with no maintenance. No maintenance means no labor costs and no replacement lamp costs associated with installed fixtures and lamps over the life of the fixture. Fixtures mounted in high or hard-to-reach locations are the prime candidates for LED lighting. LEDs are very efficient light sources and are cool to the touch, unlike incandescent light sources which release 90% of their energy generated as heat. Due to the inherent cooler running temperatures of LEDs, HVAC system design loads can be scaled down. LEDs use much less energy per fixture than standard light sources guaranteeing savings in electrical costs far into the future. Lastly, many local energy providers are currently offering rebates to customers making the switch to LED fixtures.
Environmental Impact
LEDs are easily recyclable. They contain no mercury or lead which require special handling and disposal. LEDs do no emit harmful UV/IR which discolors fabric, furniture and artwork. The U.S. Department of Energy estimates that rapid adoption of LED lighting in the U.S. by 2027 could deliver savings of about $265 billion, avoid the building of 40 new power plants and reduce lighting electricity demand by 33% in 2027.
All or even one of the above-stated reasons may be the right reason for you to choose a fixture with an LED light source
The last important factor when choosing an LED fixture is scrutinizing the manufacturer of the LED chip and the incorporation of this chip into the design of the lighting fixture. As the United States, EPA and DOE Energy Star program state on its website “Bad design can lead to a wide range of problems, some immediately observable and some not. Poorly designed products often come with exaggerated claims while failing to deliver on the quality specifications provided.” Our LED products are designed around the LED light source and not the other way around making for a well-designed, a color consistent and extra long-life fixture with a proven track record. With all our LED products, JESCO offers layout assistance and technical support helping make specification, as well as installation, simple.
Therefore, always look for reputable and trusted sources of LEDs and LED fixtures – be it JESCO
Lighting or anyone else
The SG- series of grounded fixtures and the SP- series of non-grounded fixtures can be used in undercabinet, cove, and shelf lighting as well as backlighting of signs and panels. The Sleek PlusT M can be linked for longer runs and is available in an adjustable version for better control of light output.
The Sleek Plus is an award-winning series that continues to be the leading miniature fluorescent product line in the market. This is time tested and patented collection of high-performance fixtures. The important differences between JESCO’s Sleek Plus and other similar-looking products are as follows:
These products are a line voltage system and work at standard 120V.
The Sleek Plus is linkable and has a maximum run of 360 watts in total fixtures.
This does not include any connections between the fixtures thereby extending the overall reach of the product. The overall maximum reach needs to be determined by a qualified electrician based on your power in the building
No, there is no minimal installed length.
Both the grounded and non-grounded fixtures in the Sleek PlusT M series are provided with one direct connector, SG-DC or SP-DC respectively. These direct connectors allow fixtures to be easily connected end-to-end to form one continuous run which provides a uniform and unbroken output of light.
The Sleek PlusT M product line has an extensive offering of grounded connecting cables and non-grounded connecting cables for every application – from 6” to 36”.
The Sleek PlusT M mounts with our mounting clips. Two 0⁰ and two 45⁰ clips are provided with each fixture. We also offer 90⁰ clips and fully adjustable clips which help meet any mounting situation.
No, the Sleek PlusT M is not designed for use in wet locations.
For wet location applications please refer to our DL-RS Rigid Strip LED wet location product line which is specifically designed for Wet and Outdoor installation conditions.
Yes, this product line plugs into any household or commercial two or three-prong outlet.
We offer a standard straight power cord in various lengths (grounded and non-grounded) as well as a 6-foot right-angle version that enters from the front (grounded and non-grounded) and a 6-foot right-angle version that enters from the back (grounded and non-grounded) to help meet all your wiring needs.
No. This is system is not dimmable.
It is an on/off system only controlled by a remote or in-line switch in a metal box or in a plastic box.
We offer our fluorescent lamps in a White Kelvin color temperatures of 3000°K, 3500°K, 4100°K, 5000°K and 6400°K.
The lower the color temperature the warmer the color – 3000°K is considered warm white and 6400°K is considered cool white.
We also offer fluorescent lamps in red, blue, black, and green.
Typically, you will not see any failures in our Sleek Plus for many, many years. In the rare event of a premature failure, a section can be replaced within an installed run by simply unplugging the bad section and replacing it with a new one. Lamps are also easily replaceable. For our fixed fixtures, simply pop off the protective lens and relamp – see our short video. For our adjustable fixtures, here is an instruction sheet that explains how to replace a lamp.
Recommended applications for the Sleek PlusT M series include coves, display cases, offices stores and restaurant, architectural features, corporate showrooms and exhibition display, residential shelves and counters, accenting point of purchase display, signage applications, backlighting of glass and acrylic panels or cut out forms, lighting toe-kick areas, undercabinet task lighting.